2013 Chrysler 300 Check Engine Light

Please wait while the page loads...

Check Engine Light Service 2013 Chrysler 300

What do you do when you’re driving along in your Chrysler 300 and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Chrysler owners, your heart sinks drastically because you may have definitely idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep, tranquil breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is advised that you get your 2013 Chrysler 300 checked immediately. Ignoring that warning could end up causing major, far-reaching damage to expensive engine parts.

When your 2013 Chrysler 300's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is ordinarily labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that can expeditiously identify the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Chrysler auto repair mechanics at Larry H. Miller Chrysler Jeep Dodge Ram Sandy. There are again a number of essentially inexpensive code readers that are designed for do-it-yourselfers, should you select that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the exactly correct issue and repair it.

2013 Chrysler 300 Check Engine Light

A flashing light indicates that the problem is exceedingly serious and if not taken care of expeditiously may result in major and serious damage to the car. If the check engine light in your 2013 Chrysler 300 starts flashing, that means that the problem needs attention expeditiously and your Chrysler should be brought in immediately. This blinking light normally reveals a severe engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can expeditiously raise the temperature of the catalytic converter to a point where damage is likely, requiring an pricey and major repair. Some owners ask if spark plugs cause the check engine light to flash? This can exactly be the cause. A defective, old or dirty spark plug can cause the engine to misfire. If your check engine light is repeatedly flashing, please contact our team of automotive experts at Larry H. Miller Chrysler Jeep Dodge Ram Sandy quickly by calling 3852130216. If the problem is totally ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a tremendously costly repair.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not perfectly tightened to a more serious failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it good to get the proper code reading and diagnosis. The average cost for a check engine light diagnosis & testing is usually between $88 and $111. The good news, Larry H. Miller Chrysler Jeep Dodge Ram Sandy offers entirely complimentary multi-point inspections and free diagnostics, in most cases, to help determine the cause of your check engine light.

What could cause the check engine light to come on in a 2013 Chrysler 300?

When your check engine light comes on, this could be as simple as tightening or replacing your gas cap. Also, the check engine light could also be a warning of a meaningful problem that could cause serious damage to your engine and come with a hefty and expensive repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady and continuous glow ordinarily means something less serious but a flashing check engine light signifies that your vehicle’s engine is in meaningful trouble and useful service is necessary promptly. If your check engine light is flashing in your 2013 Chrysler 300, we very recommend not to drive the vehicle and schedule Chrysler service today. Below is a list of the most common reasons your check engine light can come on:

  • The battery is low or dead. The battery in your 2013 Chrysler 300 is each vital. Without a vehicle battery, your vehicle won’t start, light up the road ahead, play the radio or charge your phone. Today’s vehicle batteries last much longer than they did a few decades ago, and they don't really require maintenance. The price of a new one depends on the type of Chrysler you drive, but check our current service coupons and specials.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Chrysler 300 is what determines how much fuel is needed to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to certain changes, like altitude. If your Chrysler 300 is having trouble starting, idling rough or has a sudden fast change in the position of the throttle pedal, this could be a essential sign of a broken mass airflow sensor.
  • Your 2013 Chrysler 300 has a vacuum leak. Each Chrysler 300 has a vacuum system that performs a wide variety of functions. The vacuum system still helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, exceptionally if they’re exposed to intense heat or extreme cold.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns more quickly and your vehicle will be less efficient when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A broken sensor can not only affect your miles per gallon, but it can cause meaningful damage to your catalytic converter and your 2013 Chrysler 300's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to determine the exactly correct mixture of air and fuel that enters the cylinders in your engine. A broken O2 sensor can still cause a vehicle to fail an emissions test.
  • One of the most common and frequent cause is that your 2013 Chrysler 300 gas cap is loose, broken or missing. The gas cap for your 2013 Chrysler 300 serves numerous purposes. It prevents dangerous gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a broken fuel cap? If your gas cap is old or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump and be more costly. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on quickly after you put gas in your 2013 Chrysler 300, first thing you should check is to make sure the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak extreme havoc on your 2013 Chrysler 300 if it’s not installed correctly. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound familiar, bring your 300 to Chrysler and have our team of gifted certified mechanics guarantee that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, exceptionally aftermarket parts and accessories, or using OEM parts first place might cost a little bit more but could help you save substantially from having to get poor work and damage caused by poor installation work corrected.
  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2013 Chrysler 300’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A broken catalytic converter is usually caused by repeatedly neglected maintenance, which is why Larry H. Miller Chrysler Jeep Dodge Ram Sandy offers a free multi-point check with each Chrysler service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Chrysler 300 will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your vehicle may run at a higher temperature, too, which can cause other perilous problems from overheating.
  • New Spark Plugs or Plug Wires are needed for your 2013 Chrysler 300. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run smooth. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or old, you will experience a evident poor performance and decreased power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, leading to more expensive repairs.

Is it safe to drive your 2013 Chrysler 300 with the check engine light on?

This question is not exceedingly simple because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be secure to drive. This is usually indicated by a steady glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more serious problem. If the check engine light is flashing, this means that there is a serious issue and it is suggested to service your Chrysler 300 quickly. Call the experts at Larry H. Miller Chrysler Jeep Dodge Ram Sandy by dialing 3852130216 so you can describe the issues. Or lessen your speed and bring your 2013 Chrysler to our certified mechanics as soon as possible.

What Does the Check Engine Light Mean?

One of the most generally misunderstood lights or indicators in your 2013 Chrysler 300 is the check engine light. The check engine light is part of the essential onboard diagnostics system, and displays in a wide range of different ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your car. Onboard computers increasingly have controlled and monitored car performance since the 80s and do a wide range of things for your 2013 Chrysler 300. Some of these essential duties include ignition timing, shifting automatic transmissions controlling engine speed, and implementing cohesion control, just to name a few. With that being said, the check engine light can mean a variety of different things. It can be as simple as your gas cap being loose or as unpredictable as engine knocking. If your check engine light is on in your 2013 Chrysler 300, contact Larry H. Miller Chrysler Jeep Dodge Ram Sandy . Our Chrysler service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is flashing. Contact Larry H. Miller Chrysler Jeep Dodge Ram Sandy today!

How many miles can you drive with the check engine light?

Since each check engine code has its own level of severity, it is typically difficult to predict how many miles you can be safe in driving with the warning light on. If you check engine light is flashing, we suggest that you pull over and contact Larry H. Miller Chrysler Jeep Dodge Ram Sandy to help determine if your car is safe to drive in or if we suggest a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly. It could be anything from a bad sensor to plug wires needing to be replaced.

2013 Chrysler 300 Check Engine Light Codes

The check engine light turning on can be quite intimidating, exceptionally to see that little light on your vehicle’s dashboard suddenly illuminate, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, still known as the OBD (on-board computer diagnostic system) in your 300. There are hundreds of different codes that your check engine light can properly represent. While that sounds daunting, with a little patience, tackling basic diagnostics will give you useful knowledge about your vehicle and will still allow that important Check Engine Light to do what it is absolutely supposed to do: be your guide. Unfortunately, obvious and useful vehicle symptoms do not regularly accompany an illuminated Check Engine Light. Since there are hundreds of imaginable OBD codes, there are still hundreds of imaginable reasons for the light, including:

  • Fuel and air metering systems problems
  • Old Battery
  • Ignition system faults
  • Computer output circuit issues
  • O2 Sensor
  • Bad Spark Plugs
  • Loose Gas Cap or Missing Gas Cap
  • Transmission issues
  • Emissions controls issues

This is why it is crucial for someone who does not have a lot of prevalent automotive knowledge to not assume what a code means. Call Larry H. Miller Chrysler Jeep Dodge Ram Sandy at 3852130216 today or schedule your check engine light service online today! If the engine light comes on due to a serious concern, you risk damaging your vehicle further by not repairing the issue right away. When your check engine light comes on, you should get it checked out quickly by a skillful certified Chrysler mechanic.

Will the check engine light reset itself?

The check engine light on your 2013 Chrysler 300 will frequently shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will expeditiously turn itself off. Likewise, if your catalytic converter is working perfectly, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Chrysler 300 light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Larry H. Miller Chrysler Jeep Dodge Ram Sandy so the light and code can be double-checked and reset.

2013 Chrysler 300 Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several common causes including something as simple as a loose gas cap. Other generally common reasons for a Check Engine Light are faulty head gasket, damaged oxygen sensor, a malfunction with the fuel injection system, damaged emissions control part, dirty mass airflow sensor, or damaged spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Chrysler Certified Technicians and the certified service protocol to isolate the root problem and completely repair it as required to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Chrysler issue was completely fixed.

Every 2013 Chrysler 300 was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the car on its important systems. The rapid sensors are continually detecting conditions while sending essential data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. Yet, unfortunately that is the limitation of the Check Engine Light – it won’t tell you what absolutely is wrong nor what to do about it. That’s where we come in; Larry H. Miller Chrysler Jeep Dodge Ram Sandy provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Highly Qualified Service professional.

Chrysler Services

Chrysler 300 Services

Recent Services Completed

  • 2013 Chrysler 300 Oil Filter