2017 Ram 3500 Alignment

$119–$179 is the typical four-wheel alignment price range at Larry H. Miller Chrysler Jeep Dodge Ram Sandy.

That range reflects dealer-performed four-wheel alignments that include a suspension inspection and factory-spec adjustments for a heavy truck like the 2017 Ram 3500. Pricing gives you an upfront expectation when you call or use the online scheduler.

• Includes caster, camber and toe adjustments to factory specs
• Before-and-after alignment printout provided
• Suspension and steering components inspected for wear

Most four-wheel alignments for a 2017 Ram 3500 take about 60 minutes from lift to road test.

The 2017 Ram 3500’s heavy-duty suspension and optional axle setups can add time if we find worn parts that require repair before alignment. Our technicians complete a pre-alignment inspection, adjust to factory spec, and perform a road test in Sandy to confirm tracking.

• Pre-alignment suspension and tire inspection
• Computerized angle measurements and adjustments
• Final road test to verify settings

Get an alignment every 2–3 years or approximately every 30,000 miles, and after any suspension work or major pothole impact.

Driving around the Sandy area—where frost heaves, canyon roads, and construction are common—can accelerate alignment drift on a heavy truck like the 2017 Ram 3500. If you tow frequently or carry heavy payloads, check alignment sooner.

• After replacing tires or suspension components
• If you hit a large pothole or curb hard
• At the first sign of uneven tire wear or pulling

Common signs include uneven tire wear, the truck pulling to one side, an off-center steering wheel, or vibration at highway speed.

Because the 2017 Ram 3500 often tows heavy loads and sees rough roads around Sandy and Draper, these symptoms can appear sooner than on lighter vehicles. If you observe any of these signs, bring the truck in for a full inspection before tires or steering parts sustain further damage.

• One tire shows faster wear than the others
• Vehicle drifts left or right while driving straight
• Steering wheel is not centered when driving straight

A four-wheel alignment includes suspension and tie-rod inspection, computerized caster/camber/toe measurement, adjustment to factory specifications, and a before-and-after printout.

The service for a 2017 Ram 3500 also includes tire pressure checks and a road test to confirm stability when towing heavy loads. Our technicians record the factory-spec targets and show you the corrected readings, so you have a clear record of the work done in Sandy.

• Tire pressure and visual suspension check
• Computerized measurement and adjustment of caster, camber, and toe
• Printed before-and-after alignment readings and road test

If tie rods, ball joints, control-arm bushings, or shocks are worn, the alignment may not hold and those parts will need repair or replacement first.

Technicians at Larry H. Miller Chrysler Jeep Dodge Ram Sandy inspect steering and suspension components before adjusting angles on a 2017 Ram 3500. If parts are out of tolerance, we’ll document the findings and recommend repairs so the alignment will remain stable under load and on local roads.

• Wear or play in tie rods and ball joints can prevent proper alignment
• Damaged control-arm bushings or bent components require repair first
• We perform a road test and post-adjustment check to confirm results

The 2017 Ram 3500 requires caster, camber and toe set to the manufacturer’s factory specifications for both front and rear axles; exact angle values depend on axle and suspension options. Dealer-level alignments use calibrated alignment racks and computerized measurement tools to restore the truck to those factory targets. Because the 2017 Ram 3500 frequently tows heavy trailers—its published towing capacity is 28,760 lb—keeping wheel angles within spec reduces steering effort, improves tire life, and helps trailer tracking. Bring your 2017 Ram 3500 to Larry H. Miller Chrysler Jeep Dodge Ram Sandy in Sandy for a factory-spec alignment — schedule service.

Our four-wheel alignment for the 2017 Ram 3500 follows a step-by-step process: inspect tires and suspension components including tie rods and ball joints; verify and set tire pressures; measure caster, camber and toe with computerized alignment equipment; adjust each angle to factory specifications; provide a printed before-and-after alignment report; and complete a final road test. If we find worn components that prevent the alignment from holding, we document and recommend repairs.

Service specials and current offers may apply — view service specials. To book the service, schedule service.

Drivers in Sandy, Draper, and South Jordan bring 2017 Ram 3500 trucks to our shop after canyon trips, construction detours, or winter road impacts. Local potholes, frost heaves, and frequent towing can knock a heavy truck’s alignment out of tolerance sooner than on a passenger car. We perform a full inspection and alignment to factory specs, then verify handling with a road test on local routes.

Located in the Sandy Auto Mall just off I-15, Larry H. Miller Chrysler Jeep Dodge Ram Sandy is convenient for commuters and weekend haulers. For directions or to book an appointment, schedule service online.