2025 Ram 2500 Alignment

About 60 minutes for a standard four-wheel alignment at our service center.

Our Sandy service bay schedules most four-wheel alignments in roughly an hour for the 2025 Ram 2500 using calibrated alignment racks and diagnostic checks. Complex suspension corrections or parts replacement can extend the visit, and we verify measurements with a road test afterward to confirm factory-spec settings.

• One-hour baseline for a four-wheel alignment
• Extended time if suspension components need repair
• Includes final road test and verification

Every 2–3 years or about every 30,000 miles is a common guideline for the 2025 Ram 2500.

Regular intervals help prevent uneven tire wear on heavy-duty trucks; for the 2025 Ram 2500, also check alignment after towing heavy loads, hitting a major pothole, or after suspension work. We recommend a quick inspection at oil changes or tire rotations to spot alignment drift early.

• Inspect alignment at each tire rotation or every 6 months
• Check after suspension or steering repairs
• Re-align after significant road impacts or trailer use

Uneven tire wear, the truck pulling to one side, an off-center steering wheel, or vibration at speed are the clearest signs.

If you notice any of these symptoms on roads around Sandy, Draper, or South Jordan — especially after hitting potholes or frost-heaved pavement — bring the 2025 Ram 2500 in for a suspension and alignment inspection. Early detection saves tire life and helps preserve steering response.

• Check tires for one-sided or cupped wear patterns
• Note any pulling left or right during steady driving
• Look for a steering wheel that is off-center when driving straight

Alignment includes caster, camber, and toe adjustments to factory specifications with before-and-after printouts and a suspension inspection.

For the 2025 Ram 2500 our service procedure measures front and rear angles, adjusts to Ram factory tolerances, and provides a printed report of the before and after readings. We also inspect tie rods, ball joints, and bushings to confirm the alignment will hold under load and road conditions common to the Wasatch Front.

• Measure and adjust caster, camber, and toe
• Inspect steering and suspension for worn components
• Provide printed before/after alignment readings and road test

Worn tie rods, ball joints, or strut mounts often require repair or replacement before an alignment will hold.

Our technicians in Sandy inspect suspension components before adjusting alignment on the 2025 Ram 2500 and will flag parts that are out of tolerance. If worn components are present we’ll explain the needed repairs and show the measurements that prevent a lasting alignment until addressed.

• Suspension inspection performed before adjustments
• Report and images of worn components if replacement is needed
• Re-check alignment after any necessary repairs

Not always — but it is worthwhile after suspension work, a major road impact, or if tires show any uneven wear.

If the 2025 Ram 2500 drives straight and tire wear is even, you can space alignments out; however, because of heavy loads and canyon driving common to the Salt Lake Valley, periodic checks catch small drifts before they worsen. We can perform a quick inspection and advise whether a full four-wheel alignment is needed.

• Quick inspection can confirm if a full alignment is necessary
• Recommended after towing, potholes, or suspension repairs
• Prevents accelerated tire wear and steering issues over time

Our four-wheel alignment service for the 2025 Ram 2500 follows a methodical sequence to restore factory geometry and verify road performance. Technicians begin with a visual and hands-on suspension inspection: tie rods, ball joints, control-arm bushings, and steering linkages are checked for wear. Tire pressures are confirmed and tires are mounted squarely on calibrated alignment turntables. We measure caster, camber, and toe on front and rear axles, make adjustments to Ram factory specifications, and produce a printed before-and-after report showing the angle corrections.

After adjustments we perform a road test to confirm steering center and highway tracking. If worn components are discovered that would prevent the alignment from holding, we document the issue and recommend repair options. For service specials see service specials, and when ready you can schedule service.

Factory alignment for the 2025 Ram 2500 sets the front and rear toe, camber, and caster to Ram engineering tolerances; exact numeric specifications vary by axle configuration and load. We use OEM-grade alignment racks and computerized sensors to match those factory targets rather than approximate settings. Common alignment callouts on heavy-duty Crew Cab trucks include slight toe corrections for long-wheelbase stability and camber bias adjustments after wheel or suspension changes.

If you frequently tow, carry payload, or drive on construction routes and canyon roads near Sandy, small deviations can accelerate tire wear and affect steering feel. Bring your 2025 Ram 2500 to Larry H. Miller Chrysler Jeep Dodge Ram Sandy in Sandy for a factory-spec alignment — schedule service.

Located in the heart of the Sandy Auto Mall, our service center supports drivers from Sandy, Draper, and South Jordan with alignment work tailored for the 2025 Ram 2500. Local road conditions — potholes from freeze-thaw cycles, occasional frost heaves, and canyon-grade routes — make periodic alignment checks practical for heavy-duty pickups. Our team documents alignment readings and inspects suspension components that commonly affect long-term tracking.

Appointments are available online and we can coordinate inspections around commuter schedules using our convenient location just off I-15. To book a visit, schedule service or review current service specials.